Monday, January 5, 2015

Body and suspension/steering

John and I rang in the new year by working on the car a bit.  With the newly refreshed trunk ready, I reinstalled (for the last time?) the gas tank and filler.  You would think she is fresh off the factory floor.



John began trying to figure out the passenger floor and support rails.  The floor itself is long gone and the rails underneath have some rusty spots.  Completely removing and replacing the rails is the best option, but it can be very tricky and is outside my comfort zone.  We will instead fit and weld a piece of steel.  It won't be pretty, but it will be structurally sound completely covered once the new floor pan is in place.
 John managed to cut the steel so it fit almost perfectly (for our purpose) into the existing rail.  That kid is wicked smart.  With the steel support set in place, to be welded later, John started to fit the floor pan.  He says it fits well and minimal cutting and shaping will be required.  Putting it permanently in place will require more welding.  Since all welds will eventually be covered, we are confident we will be up to it.  We will also need a little sheet metal to close in the front floor area. 

We also worked on the front cross member and steering rack.  We picked the better of the two steering racks, replaced the boots which keep the oil contained, and added some fresh oil.  We took some measurements to center the steering rack, and loosely installed it in the car.  It bolts to the cross member, so it is just in place and held by bungee cords right now.  



 Now freshly painted and with shock absorbers installed, the cross member was ready to be bolted back on.  I cleaned the bolts and put on the new pads.

We used the floor jack to help hold it in place while we got the nuts started.  It was an awkward, two-man job, so I have no pictures of the process.  One of us had to hold the bolt in place from the bottom and make sure the pads stayed in the right place while the other got the nuts started from the top.  Tightening three of the four nuts was relatively easy because access was easy.  The fourth nut was perfectly tucked behind one of the lines to the oil cooler (thanks again Nigel!), so John had to loosen the oil line before the fourth bolt could be secured.  Given the importance of this particular piece, we took the time to do it right.

It is really great to be installing new and improved parts.  It also means it is time to open the wallet again.  John's favorite lines: "We should replace that to be safe.  It is fairly cheap.  It is only (insert $8 - $70 here depending on the part).  I will add it to the next order."  I mean, um, thanks for all the help John.  I couldn't do it without you.

I ordered some tires from Tire Rack that arrived today.  I don't know exactly when they will be installed, but they were priced right, so I went ahead.


Up next - more body work and maybe time to try welding. 

Wednesday, December 31, 2014

Carbs and body work

John spent a great deal of time here working on the car in the past few weeks.  I probably don't remember everything we did, but here are some highlights.

Although we had the car running, something was not quite right.  We started checking issues as systematically as possible.  John wanted to eliminate electrical issues, so we started there.  John moved the battery from the trunk back to the original location behind the seats.  He put in a new ground wire and cleaned up the various contacts.


Power seemed good now, so we moved to fuel issues.  We thought it might be an issue with the carburetors.  Knowing John's work fine, we removed the carbs from his car and put them on my car.  With John's carburetors on my car, it ran just fine.  This is a good thing since we now know where to trouble shoot.  


We disconnected the fuel line and ran the pump to empty the tank back into a can.  The tank was coming off so we could work on the trunk.  I got lots of great car-related Christmas gifts including the light given by my parents in the picture below.

While John was working on carbs and electrical, I continued to disassemble the front suspension.  I finally got it all apart, cleaned, and painted.  It is almost ready to go back on the car.  Below are some before pictures.

Above is the cross-member repainted with one shock absorber installed.  Almost ready to go back on the car.    Below are some of the other suspension parts also with fresh paint.


We also addressed the large hole in the trunk.  A while ago we cut out a rusty section from the white car and a piece from the primer car to repair the hole.

John spent some time shaping the repair panel so it would fit nicely in the white trunk.

 I had to remove the gas tank to actually install the repair.  I had plenty of light to work thanks to a great Christmas gift from the Hungeling family.


 With the tank removed, John cleaned up the trunk and patched some of the holes.

 We used fasteners to hold the repair panel in place and do some more shaping.

We then used rivets and sealer to hold it in place.  Maybe not how the professionals would do it, but it is solid and water-tight.


After some cleaning and white paint it was good as new.  Well, at least a job done.


I also bought some black paint and gave the front wheel wells a quick hit with the wire wheel followed by some black spray paint.



Sunday, December 14, 2014

Major Milestone

John and I put in many solid hours this weekend (Dec 13 and 14).  He came over about 8:30 Saturday morning to get in a full day of work.  The goal was to get the car to run this weekend.  Much of the first work involved wiring.  Wiring is color-coded.  I am color blind.  That is a bad mix.  So, the wiring work falls squarely on John. He set to work with a wiring diagram and tester. 

I started working on the fuel system.  It was time to install the new fuel tank.  I had actually done this before on John's car, so I was comfortable giving it a shot.  It is a temporary installation because the trunk still needs to be repaired and the tank mounts directly to the bottom of the trunk.  The picture below shows the empty space where the trunk will be.  The round hole is where the filler neck comes up and then out of the rear of the car. 

 
Here is the new tank ready to put in place.  It isn't that heavy, but the floor jack holds it in place while I attach it. 


It is nice to have a shiny part in place.  Below are a couple of pictures of the installed tank.  The pictures aren't great because it is under the car, but it was a nice accomplishment.  


I then went to the other end of the fuel system in the front of the car.  There are solid (metal) fuel lines back to front and rubber lines (to allow a little movement of the engine) which connect to the carburetors.  I replaced the rubber lines and a fuel filter.  (For those wondering, the white cylinder in the top right of the picture is a fire extinguisher.  We are dealing with electricity and fuel today.) 


John got the car wired up, so it was time to connect the battery and see what happened.  What happened was there was sparking.  Note the appearance of the fire extinguisher once more. 


I will just blog the short version, but it turns out there was a problem with the alternator.  We actually had the wrong alternator for the car, so the wiring did not connect correctly.  Thankfully we had another alternator on hand (both shown in the picture on the left), and it had the right connections.  It is shown installed on the right.


That seemed to resolve the sparking issue.  It was now time to try turning it over.  We removed the spark plugs because we didn't really want it to run, but we wanted the oil to start circulating.  The starter worked and it was very exciting to see the engine turning over.  We installed the spark plugs, connected some more wiring, and decided it was time to try running it.  We didn't put in any fuel, but did spray some starter fluid in the carbs to see what would happen.  John stood by with starter fluid and the fire extinguisher. 


It fired up and ran for a second or so.  We were very excited and called it a day.

Sunday started a little later, but we had the goal of running the car before the day was over.  The major hurdle was the exhaust system.  What we had was rusty and incomplete.  John started cutting and grinding rust.  Our helper for the day did not care for the loud noises.


We more or less (OK, less) figured out what we were missing.  We spent quite a while in the aisles at VIP (auto parts store) piecing together an exhaust system.  We bought some flexible pipe, a minimalist exhaust, and some products to bind it all together.  What we ended up with isn't exactly what MG engineers had in mind, but I think it will work.  It should be properly loud too. Sorry Jane.


We pieced it all together and loosely attached it to the bottom of the car.  I spent a ridiculous amount of time trying to get six nuts, washers, and lock washers attached to the bottom of the exhaust manifold.  Eventually it was connected and time to try to start her up.  In all the excitement I forgot to pick up the camera.  With the help of some starter fluid, we got the car running.  It was stinky and loud, but running.

So, it is Sunday night, December 14 and the car has run.  There is a very long way to go, but it feels more like a car than it did Friday.  I really appreciate John spending his whole weekend here working on the car.  John filled the new whiteboard (thanks Elizabeth!) with a list of to-do items.  Maybe she will be on the road summer 2015.